Electronics & Instrumentation Team
The Electronics and Instrumentation Group studies, designs, and builds custom electronic systems for the laboratory’s research projects, conducted through national and international collaborations. Its activities cover a wide range of disciplines, from hardware design to software development.
Our Areas of Expertise
• Firmware and FPGA Development: Expertise in the design of programmable logic devices (FPGAs) and high-speed serial links, with applications integrated into major physics projects (such as the CMS calorimeter).
• Data Acquisition Chains: Expertise in data acquisition for physics detectors, ASIC control and readout, as well as the design and routing of complex HDI boards complying with IPC standards.
• Hardware / Software Synergy: A combined approach pairing electronic board development with the creation of dedicated software environments for acquisition, control-command, and data processing.
Collaborations and Outreach
The group works in close collaboration with IT teams to ensure efficient co-design between the hardware and software aspects of detectors. Members are also involved in knowledge transfer through the training of students and interns, scientific publications, and conference presentations.
Outlook and Strategic Vision
To maintain its expertise and anticipate the evolution of modern electronics, the group embeds its activities in an ongoing technology watch process. This forward-looking vision relies on several pillars:
• Evolution of Embedded Architectures and Processors: Ongoing exploration of open hardware solutions (such as RISC-V architectures) to optimize future electronic systems.
• Methodological Mastery and Rigor: Continuous reinforcement of verification and software validation methods on FPGA targets to ensure robustness, reliability, and optimal code coverage in complex developments.
• Preservation of PCB Design Expertise: Investment in advanced simulation skills and signal integrity analysis to anticipate tomorrow’s technological challenges and ensure cutting-edge achievements.
FPGA Developments
The group has built recognized expertise in the development and implementation of electronic systems featuring high-speed serial links and programmable devices such as FPGAs. For these devices, dedicated algorithms have been developed in the form of firmware, notably for the trigger electronics of the electromagnetic calorimeter sub-detector (CMS experiment)
The group relies mainly on the AMD (Xilinx) development toolchain. Designs are first validated through simulation with ModelSim/Questa before being synthesized, placed and routed with AMD (Xilinx) tools.
These developments drive the group to take on ever more ambitious technical challenges, both in the design and implementation of algorithms and in the use of the design methods and tools at its disposal. They allow the group to stand today as one of the leading players in FPGA firmware development for CNRS Nucléaire & Particules (IN2P3).
DAQ & Instrumentation developments
Another area of the group is its mastery of data acquisition chains for particle physics detectors, implemented together with their sensors and associated electronics. Drawing on the proximity of the UMS OMEGA and the CEA/IRFU microelectronics group for several projects in which the laboratory is involved, the group develops the electronics for the control and readout of ASICs designed by these teams.
In this context, the group’s engineers apply their expertise in digital electronics on programmable devices to structure data transfer and control systems. For the characterization of front-end ASICs for the experiments to which the group contributes, it deploys test platforms based mainly on commercial evaluation boards, notably from AMD (Xilinx), on which validation firmware is developed. These platforms are paired with control software designed by the online software engineers who collaborate with the group.
The group also has expertise in sensor characterization, PIN diode wafers, SiPMs, photomultiplier tubes or detector as part of its involvement in a multidisciplinary laboratory project.
Finally, it contributes to the technical support of the robotic platform used to test the production of thousands of ASICs, such as the 120,000 ASICs equipping the HGCAL sub-detector of the CMS experiment.
CAD developments
To meet the needs of researchers and projects, the group’s electronics engineers design electronic boards using Computer-Aided Design (CAD) tools. The group uses the Cadence suite: System Capture for schematic entry, Allegro for component placement and printed circuit board routing, and Sigrity for electromagnetic simulations, signal and power integrity simulations along with the Polar tool for layer stack-up definition.
These tools make it possible to control key parameters, such as the characteristic impedance of transmission lines, the geometry of component footprints and pads, or the electrical behavior of the multilayer board (for example, signals passing from one layer to another through vias), ensuring the quality and reliability of the systems.
Their use relies on technical expertise (electromagnetism, multilayer PCB manufacturing, mechanical and system integration) and on human skills (relations with suppliers, adaptation to late changes, dialogue with physicists and the group’s engineers), within the allocated budgets. Finally, the digital nature of these tools eases exchanges with suppliers and partner laboratories, the transmission of manufacturing and assembly files, and the long-term follow-up of projects over many years.
